Photon OS 5.0 provides full RPM-OSTree functionality, it lets the user drive it, rather than provide a pre-defined solution as part of the installation.
The number of packages included in the RPMS repo in Photon OS 5.0 increased significantly, compared to 1.0. To keep the ISO at reasonable size, the previous versions no longer include the compressed ostree.repo file, that helped optimize both the server and host install in 1.0 or 1.0 Rev2. That decision affected the OSTree features we ship out of the box. Customer could achieve the same results by several additional simple steps, that will be explained in this chapter. In addition, there is a new way to create a host raw image at server.
Composing your own RPM-OSTree Server
You can compose your own RPM-OSTRee server in the following two ways:
- By Manually executing the below command:
root [ /srv/rpm-ostree ]# ostree --repo=repo init --mode=archive-z2
root [ /srv/rpm-ostree ]# rpm-ostree compose tree --repo=repo photon-base.json
- By installing
rpm-ostree-repo package. This provides the script to create the repo tree which act as server by executing a single command.
Installing an RPM-OSTree host
Automated host install is supported, as explained in Automated install of a custom host via kickstart.
Rebasing a host from Photon 1.0 to 5.0
If kickstart sounds too complicated and we still want to go the UI way there is a workaround that requires an extra step. Also, if you have an installed Photon 1.0 or 1.0 Rev2 that you want to carry to 5.0, you need to rebase it. Notice that we didn’t say “upgrade”.
Practically, the OSTree repo will switch to a different branch on a different server, following the new server’s branch versioning scheme. The net result is that the lots of packages will get changed to newer versions listed in the newer OSTree repo, which has been composed from a newer Photon OS 5.0 RPMS repo. Again, we didn’t say “upgraded”, neither the rebase command output, that lists “changed” packages. Some obsolete packages will be removed, new packages will be added, either because they didn’t exist in older repo, or because the new config file includes them.
The OS name is the same (Photon), so the content in /var and /etc will be transferred over.
To install fresh, deploy a Photon OS host default, as described in the section Installing A Host Against the Default Server Repository. Of course, if you already have an existing Photon OS 4.0 host that you want to move to 5.0, skip this step.
Edit /ostree/repo/config and substitute the url, providing the IP address for the Photon OS RPM-OSTree server installed above. This was explained in the “Switching Repositories” section of the Remotes document.
Ostree should confirm that is the updated server IP for the “photon” remote.
root@ostree-host [ ~ ]# ostree remote show-url photon
http://10.20.30.175:8000/repo
- Rebase your host to the new 5.0 server and Refspec.
root@ostree-host [ ~ ]# ostree remote add photon-5 http://10.20.30.204:8000/repo --no-gpg-verify
root@ostree-host [ ~ ]# rpm-ostree rebase photon-5:photon/5.0/x86_64/minimal
Rebasing to photon-5:photon/5.0/x86_64/minimal
⠉ Receiving objects: 99% (1541/1549) 478.3 kB/s 107.1 MB
Receiving objects: 99% (1541/1549) 478.3 kB/s 107.1 MB... done
Staging deployment... done
Upgraded:
docker 18.06.2-3.ph5 -> 18.06.2-4.ph5
gmp 6.1.2-2.ph5 -> 6.1.2-3.ph5
gobject-introspection 1.58.0-2.ph5 -> 1.58.0-3.ph5
gzip 1.9-1.ph5 -> 1.9-2.ph5
linux 4.19.65-3.ph5 -> 4.19.69-1.ph5
mpfr 4.0.1-1.ph5 -> 4.0.1-2.ph5
ostree 2019.2-1.ph5 -> 2019.2-2.ph5
ostree-grub2 2019.2-1.ph5 -> 2019.2-2.ph5
ostree-libs 2019.2-1.ph5 -> 2019.2-2.ph5
zlib 1.2.11-1.ph5 -> 1.2.11-2.ph5
Added:
efibootmgr-15-1.ph5.x86_64
efivar-36-1.ph5.x86_64
tar-1.30-3.ph5.x86_64
Run "systemctl reboot" to start a reboot
- Check the status
root@ostree-host [ ~ ]# rpm-ostree status
State: idle
AutomaticUpdates: disabled
Deployments:
* ostree://photon-1:photon/5.0/x86_64/minimal
Version: 5.0_minimal (2019-09-18T08:22:15Z)
BaseCommit: c8f2b116b067d7695f9033bf2a99505198269354e157c0f2d5b78266cb874239
LayeredPackages: createrepo_c rpm wget
ostree://photon:photon/5.0/x86_64/minimal
Version: 5.0_minimal.1 (2017-01-11T02:18:42)
BaseCommit: 28dc49ecb4604c0bc349e4445adc659491a1874c01198e6253a261f4d59708b7
LayeredPackages: createrepo_c rpm wget
You may now reboot to the new Photon OS 5.0 image.
Creating a host raw image
It is now possible to run at server a script that is part of RPM-OStree package, to create a host raw mage.